Local contractor in 55318

A malfunctioning air conditioning unit prompted us to assess and resolve the issue. We replaced the motor/compressor starter for the AC condensing unit and conducted a run test with temperature differential recording to ensure the system was operating efficiently. The job was completed in Chaska, and the AC is now functioning smoothly.

A malfunctioning air conditioning system prompted our visit to Chaska. We performed a thorough inspection, added the first pound of R410A refrigerant, and applied a leak seal and dye additive to identify any potential leaks. Additionally, we recommended replacing a condenser capacitor for improved reliability and advised on ongoing maintenance tips for optimal performance.

A full AC check-up was performed to ensure the efficient operation of the unit. This included inspecting valve caps, wrapping line-sets, rinsing the condenser, and checking pressures and temperature drops. Additionally, we leveled the existing condenser using rubber pads and performed a cut test for the main plumbing vent. Comprehensive maintenance was conducted to uphold optimal performance.

A water heater replacement was needed for the homeowner in Chaska. We installed a new commercial grade Bradford-White 50-gallon power vent water heater, ensuring reliable hot water supply. The installation included a six-year manufacturer warranty for the tank and a one-year workmanship warranty for all connections. Additionally, we took care of hauling away the old water heater, leaving the property ready for use.

A malfunctioning water heater prompted us to install a commercial-grade 50-gallon General Electric electric water heater, complete with an eight-year manufacturer tank warranty. We also addressed issues with the emergency backup pump by reconfiguring and stabilizing the pumps, and fixing the weep hole issue with new piping. This comprehensive work ensured optimal performance of the water heating system in Chaska.

A blower replacement was necessary to enhance the efficiency of the HVAC system. We replaced the PSC blower motor and conducted a thorough rinsing of the blower wheel. Additionally, we performed a carbon monoxide test and measured the temperature rise to ensure optimal performance and safety of the system.

A broken furnace needed immediate attention. We conducted a thorough calibration and troubleshooting process, which included assessing the blower capacitor and flame sensor, ensuring CO levels were safe, and adjusting the gas pressure. Additionally, we increased the blower speed to achieve the desired temperature rise while verifying the wiring to the Nest thermostat. The outdoor AC unit was also addressed as part of the service.

A broken furnace needed immediate attention. We conducted a thorough service call, which included calibration and troubleshooting. During our assessment, we found that the gas pressure and fan speeds had not been adjusted properly during installation. After making the necessary adjustments, the furnace operated smoothly without any issues.

A malfunctioning furnace required our attention to ensure optimal performance. We conducted a thorough inspection, where the unit operated without any issues for over 20 minutes. The temperature rise was good, and we verified that the motors were functioning properly. Additionally, we tested the flame sensor and found no immediate concerns. However, we noted that the Nest thermostat lacked a "c" wire, which could lead to intermittent problems. We recommended the installation of a power extender kit to resolve this issue, and suggested a flame sensor replacement based on its age.

A malfunctioning zone board prompted us to replace it with a new Honeywell HZ311 zone panel. We conducted thorough testing of the heating system, including a carbon monoxide test and temperature rise check, to ensure everything operated smoothly. The replacement ensures reliable heating for the home in Chaska.

A broken furnace prompted our visit to Chaska. During our assessment, we discovered a plugged air filter and a failed zone board. To ensure the heating system operated effectively, we bypassed the zone board temporarily until the required part can be sourced. An estimate will be provided for the part replacement, including a credit for the troubleshooting fee if the customer proceeds.

A malfunctioning furnace required our immediate attention. We assessed the system, replaced the PSC blower motor, and performed necessary checks to ensure its optimal operation. This included conducting a CO test and measuring the temperature rise. With the repairs completed, the furnace was restored to functioning properly, ensuring comfort during the customer's absence in Chaska.

A malfunctioning water softener prompted us to install a new Brass Master 32k grain water softener for Tim in Chaska. We handled all necessary connections and removed the old tanks efficiently. This upgrade will greatly improve water quality for the household by reducing hardness and enhancing appliance longevity.

A water quality assessment was conducted at the residence in Chaska. We performed a comprehensive water lab test to evaluate the system's efficiency before and after the installation of the water softener. Additionally, we completed a furnace check-up, ensuring all components were operating correctly. The findings will help maintain optimal performance and enhance the homeowner's comfort.

A failing water heater required our attention. We removed the existing unit and installed a new gas water heater, ensuring all necessary plumbing and gas connections were properly managed. The old unit was responsibly hauled away, providing the homeowner with a seamless transition to their new system.

A broken air conditioning unit created a need for prompt attention. We replaced the motor/compressor starter on the AC condensing unit, ensuring proper functionality with a run test and temperature differential recording. Additionally, we installed the venting for a portable AC unit, providing a reliable solution for cooling in Chaska.

A malfunctioning air conditioning unit prompted our visit. We replaced the blown fuses at the AC disconnect and checked the refrigerant levels. During our electrical troubleshooting, we discovered that the existing fuses were undersized. We upgraded them to 30A fuses for better performance and recommended switching the Cutler-Hammer breaker to 30A as well.